Instruments & Meters

SinceVision Launches SGI-N030W Wide-Spot Laser Displacement Sensor

Zorica IlicNovember 17, 20265 min read0 views

At a glance

  • The SGI-N030W combines an expanded laser spot, 50 kHz sampling and paired sensor synchronisation for micrometre-level measurement on textured surfaces and battery electrode webs.
  • SinceVision has introduced the SGI-N030W, a wide-spot laser displacement sensor intended to stabilise non-contact measurement on rough and irregular surfaces. The company cites micrometre-level specifications and a proposed dual-sensor setup for in-line battery electrode thickness checks, with semiconductor and precision-assembly applications also targeted.
Conceptual illustration of two industrial laser sensor heads positioned above and below a moving coated foil web, with an elliptical light spot projected onto the material.

SinceVision has introduced the SGI-N030W, a wide-spot laser displacement sensor for high-speed, non-contact dimensional measurement on rough, textured and irregular surfaces. The product extends the company’s SGI Series and is aimed at lithium-ion battery manufacturing, semiconductor processing and precision mechanical engineering, where micrometre-level measurement is required.

The sensor uses an expanded laser spot with optical triangulation. SinceVision says the design is intended to reduce the instability that conventional point-spot laser systems can encounter when surface finishes vary across a part.

Wide spot targets surface-related signal noise

Conventional point-spot sensors concentrate reflected laser energy on a small area. Microscopic features such as scratches, grain boundaries, brushed textures and matte finishes can therefore alter the return signal, and those variations may be interpreted as dimensional changes. In production, that can lead to false defect warnings and additional inspection.

The SGI-N030W collects reflected light across a broader area and averages localised microscopic peaks and valleys before signal conversion, according to the company. This is intended to reduce the influence of surface roughness and optical scattering. SinceVision identifies drawn metals, sandblasted surfaces and coated battery foils as materials that can benefit from the wider spot.

Specifications support fast, synchronised measurement

The sensor has a 30 mm reference distance and a ±5 mm measurement range. SinceVision specifies repeatability of 0.05 µm on a diffuse white target under static conditions, with linearity of ±0.02% of full scale. A 50 kHz sampling frequency, equivalent to a 20 µs update interval, is intended to support high-speed measurement and monitoring of dynamic processes.

Communication options include RS485, 100Base-TX Ethernet and switchable analogue outputs for 4–20 mA current or 0–10 V voltage signals. Master-slave synchronisation allows two sensors to operate in opposition, measuring from either side of a component or moving material.

Battery electrode thickness is a primary target

One of the main applications identified by SinceVision is in-line thickness measurement of lithium-ion battery electrodes. Coating thickness and uniformity affect energy density, internal resistance and long-term cell stability. Conventional offline checks with contact micrometers or drop indicators can introduce operator variability and may deform wet or uncured electrode material. Periodic spot measurements also cannot provide continuous coverage across an entire production reel.

The proposed inspection arrangement uses two synchronised sensors positioned above and below a moving electrode web. Mounted on a calibrated, low-thermal-expansion marble gantry, the opposing heads measure their respective clearances to the material. A controller combines these readings with the fixed mounting datum to calculate absolute electrode thickness in real time.

SinceVision reports that production trials achieved stable, repeatable thickness measurement within ±0.3 µm at a web speed of 300 mm/s. The 50 kHz sampling rate is intended to provide high longitudinal resolution, allowing localised coating agglomerations, edge thinning and exposed substrate areas to be detected before the material proceeds to cell winding.

Semiconductor and precision-assembly uses

The sensor is also intended for semiconductor manufacturing, where non-contact measurement is important for sensitive wafer surfaces. Potential uses include wafer position verification, edge detection, height measurement, and checks of wafer seating and chuck alignment in atmospheric transfer modules and vacuum load-lock systems.

In precision assembly, the SGI-N030W can monitor the movement of voice coil motors, linear actuators and micro-steppers. Its sampling rate is intended to capture transient displacement, mechanical oscillations, settling behaviour and end-stop overshoot across the full range. Position data can be sent to machine control systems through the Ethernet interface for real-time monitoring and process control.

Company highlights false-warning problem

Jack Li, Global Sales and Marketing Director at SinceVision, says surface texture remains a recurring source of false defect warnings in battery manufacturing and precision assembly. He explains that conventional point-beam laser sensors can treat microscopic scratches and rough coatings as actual thickness variations, slowing production lines and creating a need for manual inspection. The SGI-N030W’s expanded spot is designed to average out those surface-related variations, while synchronisation between opposing heads supports high-speed thickness verification.

Reported by Zorica Ilic, Network Test, Infrastructure and Sourcing Editor.