Automotive Accessories

Tremec's Manual Gearbox Turns the C8 Corvette Into a Three-Pedal Car

Sofia MarchettiNovember 17, 20265 min read0 views

At a glance

  • A one-off Peitz Performance race build shows the manual transaxle fits the mid-engine C8 with little more than a tunnel cut, but the gearbox alone is priced around $75,000.
  • Tremec has engineered a six-speed manual transaxle that installs in the mid-engine Chevrolet Corvette C8 with minimal modification, and journalists sampled it in a one-off race car at a private Michigan track. Cost and the absence of a production program keep it a proof of concept for now.
A concept cockpit view shows a manual gear lever emerging from the center console and a clutch pedal in a stripped footwell, with a cutaway of the rear transaxle beside it in a trackside workshop setting.

Tremec has built a working manual-transmission version of the mid-engine Chevrolet Corvette C8, and the company let a small group of journalists and prospective customers drive it at a private track in Michigan. The car, a one-off Peitz Performance race build, shows that a third pedal can be added to the C8 without the clean-sheet engineering General Motors once cited as the reason for selling the car only with a dual-clutch automatic.

The C8 was a major pivot for Chevrolet: the first Corvette with its engine behind the driver, and the first offered exclusively with a dual-clutch transmission. Developing two transaxles—one manual, one automatic—that could work with a mid-engine layout would have been costly, and the automaker is widely understood to have chosen the automatic to protect its budget and stay competitive in comparison tests. That left the small share of buyers who wanted to shift for themselves without a factory option.

Tremec, which supplies the six-speed manual used in several GM performance models including the Camaro and the Cadillac Blackwing cars, built its own C8 development vehicle to demonstrate that the gearbox could work. Journalists were invited to sample it alongside the company's broader transmission lineup at Motorsports Gateway, a new private circuit outside Howell, Michigan.

A race car with no concessions to comfort

The test car is a track-only build. The cabin has effectively no trim, the shifter protrudes from the space normally occupied by the storage cubby and automatic selector, and the interior is fitted with a full roll cage and harnesses. The seat has virtually no adjustment, which suited the car's regular driver but not the 5-foot-7-inch reviewer, who struggled to reach the pedals cleanly and found heel-and-toe downshifts awkward. With a green track surface on a November afternoon, that limitation kept speeds in check.

Minimal changes to the car

Peitz Performance did not have to reengineer the Corvette to accept the manual. The center tunnel was cut to mount the clutch pedal hardware, but the gearbox sits in the same location as the factory dual-clutch unit and needs no special mating parts. The pedal box, notably, has enough room for a clutch and still feels roomier than the one in the previous-generation Camaro.

Because the transmission is a transaxle, the shifter is mounted remotely and linked by cables, one of which runs rearward toward the gearbox. That arrangement makes the shift action a little less precise and less mechanical than the front-engine TR-6060, though it smooths off some of the gearbox's rougher edges. Drivers who prefer a more mechanical feel may miss the direct linkage; the alternative would be moving the engine forward or the driver rearward, neither of which suits the C8's layout.

Cost remains the obstacle

The bigger hurdle is price. Tremec puts the gearbox alone at roughly $75,000, which means a converted C8 would cost about as much as a showroom-spec Z06. The company says the price will fall as volume rises, and it reports interest from automakers that may include but are not limited to GM—unspecified, but described as brands seeking a high-torque manual transaxle. For now, the manual C8 remains a demonstration vehicle rather than a production option.

Reported by Sofia Marchetti, Interior Accessories and Fitment Analyst.